Stainless Steel Shafting
Quick filters
Filters
List of products
Stainless steel shaft stock – round bar for machining
In the shop and on machine drawings, stainless round bar that will become a shaft is simply called stainless steel shafting or shaft stock. It is turned into axles, pins, drive shafts, bushings and mixer parts. This category collects the diameters most often ordered for turning – from 10 to 100 mm (about 3/8 in to 4 in) – in grades that machine well. All sizes are metric. Every bar is cut to the length you need, so you don't have to buy a full mill length. The complete range is in stainless steel round bars.
Which grade for a stainless steel shaft?
- 304 (1.4301) – the all-purpose stainless shaft for axles and machine parts running in air, in municipal water and in food-processing equipment. See 304/304L stainless steel round bar.
- 316L (1.4404) – molybdenum-bearing grade for seawater, brine, swimming pools and chlorinated cleaning agents. See 316L stainless steel round bar.
- 431 (1.4057) – pump shafts, drive shafts and pins that need clearly higher strength than 304 while keeping good corrosion resistance. See 431 stainless steel round bar.
- 303 (1.4305) – free-machining grade with added sulfur: short chips and fast production turning. It welds poorly and has lower corrosion resistance than 304.
- 420 (1.4021) – hardenable martensitic grade for shafts and axles exposed to wear. See 420 & 431 stainless steel round bar.
Diameter, machining allowance and tolerance
If the shaft will be turned, order bar a few millimeters larger than the finished diameter – the allowance lets you remove the as-rolled surface layer and clean up to a true, round surface. For example, a finished 30 mm shaft is usually turned from 32–35 mm bar. The diameter tolerance and theoretical weight are given on each product page. Shafting for linear bearings must additionally be precision ground to an h6 tolerance – the bars in this category are starting stock, not ground linear shafting.
Frequently Asked Questions
What is the difference between stainless steel shafting and round bar?
None – it is the same product. "Round bar" is the catalog name; "shafting" or "shaft stock" is what machinists call round bar that will be turned into an axle, pin or shaft.
What bar diameter should I order for a finished 30 mm shaft?
Usually 2–5 mm larger, i.e. 32–35 mm. The allowance lets you remove the as-rolled surface and correct runout. For long, slender shafts, increase the allowance.
Can I use these bars for linear bearings?
Only as starting material. Linear shafting must be precision ground to an h6 tolerance. We do not grind bars – that is done by a machine shop.
What diameter tolerance do the bars have?
It depends on how the bar is made: cold-drawn bars are usually h9 (DIN 671), hot-rolled bars k12 (DIN 1013). The tolerance of each bar is given on its product page.
Which grade for a water pump shaft?
For municipal water, 304 is enough. For pool water, seawater, brine and anywhere chlorine is present, choose 316L. If the shaft transmits high torque, consider 431 – it is much stronger, but its corrosion resistance is lower than 316L.
What is the difference between 303 and 304 stainless?
303 (1.4305) contains added sulfur, which breaks up the chips and makes turning faster. On the other hand it welds poorly and is less corrosion resistant than 304, so it is used for high-volume turning of small parts rather than welded structures.
Is a stainless steel shaft magnetic?
304, 316L and 303 are practically non-magnetic as supplied (after heavy cold working they may attract a magnet slightly). The martensitic grades 431 and 420 (1.4021) are magnetic.
Can the shaft be hardened?
304, 316L and 303 cannot be hardened by heat treatment. The martensitic grades 420 (1.4021) and 431 (1.4057) can be hardened.
How do I calculate the weight of a shaft?
The theoretical weight of each length is given on the product page. For another length, a good approximation for stainless round bar is: weight in kg per meter ≈ 0.00623 × diameter² (diameter in mm). For example, a 30 mm bar weighs about 5.6 kg per meter.
Can you cut the bar to length?
Yes. You choose the length on the product page and we cut the bar with a band saw, tolerance −0/+5 mm. A band saw does not leave a perfectly smooth cut face.
If I order several pieces, will they come as one length?
No, several pieces of the same product are shipped as separate lengths. Cutting to a different length is possible after consulting our shop staff.
Can I get a 3.1 certificate?
Yes, an EN 10204 3.1 inspection certificate (often called a mill test report, MTR) is available on request for a fee. It shows the grade, heat number and chemical composition of the material.
When will you ship my order?
We ship the order or have it ready for pickup within 3 business days after the payment is received. Within the EU we deliver by courier. If an order is fulfilled in parts, some items may arrive in a separate shipment.
Do you ship to the US?
Delivery outside the EU, including to the United States, is arranged individually. Email us the products and quantities and we will get back to you with the options.
Can I pick up the order in person?
Yes, at our warehouse at ul. Pszczyńska 140, Warszowice, Poland, once we have notified you that the order is ready for pickup.
Do you issue a VAT invoice?
Yes, we issue a VAT invoice for your order.
Can I return the goods?
Consumers may withdraw from the purchase within 14 days of delivery if the goods are unused and undamaged; the return shipping cost is paid by the buyer. Goods made to an individual order, i.e. with a specification other than on the product page, cannot be returned.
I need a larger quantity or a non-standard size – what should I do?
Email [email protected] or call +48 660 621 705. Tell us the product, grade, dimensions and quantity and we will prepare a quote.